Belinostat

Recommended Dosage in Patients with Renal Impairment Beleodaq dosage in patients with moderate renal impairment (creatinine clearance [CLcr] 30 to <60 mL/min) is 500 mg/m 2 administered over 30 minutes by intravenous infusion once daily on Days 1 through 5 of a 21-day cycle. Avoid use of Beleodaq in patients with severe renal impairment (CLcr < 30 mL/min).

No dosage adjustment is recommended for patients with mild renal impairment (CLcr 60 to < 90 mL/min).

Recommended Dosage in Patients with Hepatic Impairment Beleodaq dosage in patients with moderate hepatic impairment (total bilirubin > 1.5 to 3 x ULN, any aspartate aminotransferase (AST)) is 500 mg/m 2 administered over 30 minutes by intravenous infusion once daily on Days 1 through 5 of a 21-day cycle. Avoid use of Beleodaq in patients with severe hepatic impairment (total bilirubin > 3 x ULN, any AST).

No dosage adjustment is recommended for patients with mild hepatic impairment (total bilirubin ≤ 1.5 x ULN, any AST). Hepatic impairment is defined per the National Cancer Institute Organ Dysfunction Working Group.

Preparation and Administration Beleodaq is a hazardous drug. Follow applicable special handling and disposal procedures. 1 Preparation: Aseptically reconstitute each vial of Beleodaq by adding 9 mL of Sterile Water for Injection into the Beleodaq vial with a suitable syringe to achieve a concentration of 50 mg of belinostat per mL.

Swirl the contents of the vial until there are no visible particles in the resulting solution. If not used immediately, the reconstituted product may be stored for up to 12 hours at room temperature (15°C to 25°C; 59°F to 77°F). Aseptically withdraw the volume needed for the required dosage (based on the 50 mg/mL concentration and the patient’s BSA [m 2 ]) and transfer to an infusion bag containing 250 mL of 0.9 % Sodium Chloride Injection.

If not used immediately, the infusion bag with drug solution may be stored at room temperature (15°C to 25°C; 59°F to 77°F) for up to 36 hours including infusion time. Visually inspect the solution for particulate matter. Do not use if cloudiness or particulates are observed. Administration: Connect the infusion bag containing drug solution to an infusion set with a 0.22 micron in-line filter for administration.

Infuse intravenously over 30 minutes. If infusion site pain or other symptoms potentially attributable to the infusion occur, the infusion time may be extended to 45 minutes.

Preparation and Administration Beleodaq is a hazardous drug. Follow applicable special handling and disposal procedures. 1 Preparation: Aseptically reconstitute each vial of Beleodaq by adding 9 mL of Sterile Water for Injection into the Beleodaq vial with a suitable syringe to achieve a concentration of 50 mg of belinostat per mL.

Swirl the contents of the vial until there are no visible particles in the resulting solution. If not used immediately, the reconstituted product may be stored for up to 12 hours at room temperature (15°C to 25°C; 59°F to 77°F). Aseptically withdraw the volume needed for the required dosage (based on the 50 mg/mL concentration and the patient’s BSA [m 2 ]) and transfer to an infusion bag containing 250 mL of 0.9 % Sodium Chloride Injection.

If not used immediately, the infusion bag with drug solution may be stored at room temperature (15°C to 25°C; 59°F to 77°F) for up to 36 hours including infusion time. Visually inspect the solution for particulate matter. Do not use if cloudiness or particulates are observed. Administration: Connect the infusion bag containing drug solution to an infusion set with a 0.22 micron in-line filter for administration.

Infuse intravenously over 30 minutes. If infusion site pain or other symptoms potentially attributable to the infusion occur, the infusion time may be extended to 45 minutes.